MeasureFloorPlan

Home › Learn › Wall Type Legend: How to Read Partition Types and Wall Tags

Part of: What Is a Takeoff in Construction? How to Do One From Plans

Wall Type Legend: How to Read Partition Types and Wall Tags

Wall Type Legend: How to Read Partition Types and Wall Tags

A wall type legend, also called a wall type schedule or partition types, is the key that tells you how each wall on the floor plan is built. Every wall gets a short tag on the plan, and the legend spells out the studs, board layers, insulation, fire rating, height and sound rating behind that tag. For a drywall or framing bid, it is the sheet that turns wall lengths into material.

Measure Plans in Minutes

Upload your full plan set. Get every length, area and count. Export the takeoff to Excel.

A floor plan drawing, not a photo of a room.
Plans from $9 a month. 100% money-back guarantee.

Where is the wall type legend in a plan set?

Look in the architectural sheets, the A series. It may share a sheet with the first floor plan or get a sheet of its own near the front of the A drawings. One architect's published partition types standard, for example, is drawn as sheet A010u.

If you cannot find it, check the sheet index on the cover. The index and the order of the disciplines are covered in the guide to how to read blueprints for construction.

How do wall tags on the floor plan link to the legend?

Each wall on the plan carries a small tag, usually a letter, a number or both, placed on or next to the wall. The same tag appears in the legend with a drawing of the wall cut in plan or section and a short description. Find the tag on the plan, find it in the legend, and you know what is inside the wall.

Some offices pack more into the tag. One architect's standard builds it from a fire rating (1 for a 1 hour fire barrier, 2 for 2 hour), a letter for the partition type (A for a metal stud wall, deck to deck, one layer of gypsum board each side), a number for the nominal stud width (4 for a 3-5/8 inch metal stud, 6 for a 6 inch one) and a lowercase modifier (a for 3/4 inch plywood reinforcing to 10'-0" AFF). The same sheet shows a chase wall type where the single layer of Type X board goes on the side of the wall that carries the tag. Tag placement can carry meaning, so read the legend notes before you measure.

What does each wall type entry tell you?

Legends differ by office, so treat the table below as the typical contents and the legend in your set as the rule. Abbreviations such as GYP BD, MTL and OC are spelled out in the set's own list; see construction abbreviations on blueprints if one is new to you.

Item in the entryWhat it tells youWhat it does to the takeoff
Stud size and spacingMetal or wood, width (3-5/8", 6"), gauge, and spacing such as 16" OCStud count and track or plate LF
Board layers each sideHow many layers of gypsum board on each face, and the thicknessMultiplies the board SF
Board typeRegular, Type X, moisture or abuse resistantWhich product you price
InsulationSound batts or blankets in the cavity, or noneBatt SF, usually one layer of wall area
Fire ratingHours, plus the tested design it followsBoard type, layers, sealant at the head
HeightDeck to deck, 6" above ceiling, to ceiling, or below ceilingThe height you multiply by
STCSound Transmission Class targetOften the reason batts or extra layers are called

Common board thicknesses are 1/2 and 5/8 inch, and Type X drywall has glass fibers in the core so it resists fire longer. A legend that says "5/8 TYPE X GYP BD" is asking for that board, not regular 1/2 inch.

W1SAMPLE ENTRY (HYPOTHETICAL)16" OCTYPE W13-5/8" MTL STUDS @ 16" OC(1) LAYER 5/8" TYPE X GYP BD EA SIDESOUND BATTS IN CAVITYDECK TO DECK1 HR, TESTED DESIGN PER PROJECT LEGENDSTC PER PROJECT LEGENDGray: gypsum boardBlue: metal studsOrange: sound batt

How do you read the fire rating on a wall type?

The legend gives the rating in hours and points to the tested assembly it is built to. That design is what you follow, including the board type and the number of layers. Do not swap in a different board without checking it against the design.

Two sources come up often. UL lists steel stud and gypsum board wall designs in its U400, V400, W400 and U4100 series on Product iQ, tested to UL 263. The Gypsum Association publishes GA-600, its Fire Resistance and Sound Control Design Manual. The 2021 edition covers nearly 800 fire and sound rated systems, and model building codes, the IBC among them, have referenced the manual since 1973.

Wall height: to deck, above ceiling or to ceiling

Height is easy to skip, and it moves the board quantity a lot. A wall that runs deck to deck gets board all the way to the structure. A wall that stops above the ceiling might end 6 inches past the ceiling grid, which is how one architect's standard details its partial height types.

Floor to deck heights come from the building section. Ceiling heights come from the reflected ceiling plan or the room schedule, and the room finish schedule is often where the ceiling height and the wall finish for each room sit side by side.

What does STC mean on a wall type?

Sound Transmission Class is a single number rating of how well a partition blocks airborne sound, defined in ASTM E413 from lab tests under ASTM E90. Higher is better.

For scale: a single wood stud wall with one layer of 1/2 inch drywall each side rates about STC 33 with an empty cavity, and about STC 39 with fiberglass insulation added. When a legend calls a higher STC, expect batts, extra layers or special framing, all of which show up in your quantities.

Worked example: a drywall takeoff from the wall type legend

Here is the formula, then a small floor with three hypothetical wall types tagged W1, W2 and W3. Measure linear feet of wall for each type on the plan, then:

Board SF = LF of wall type x height x layers per side x sides

The building section shows 12'-0" floor to deck. The ceiling is at 9'-0", so a wall that stops 6 inches above it gets 9'-6" (9.5 ft) of board.

Type (sample)BuildLFHeightLayers x sidesBoard SF
W13-5/8" MTL stud, 1 layer 5/8" Type X each side, batts, deck to deck8612 ft1 x 22,064
W22-1/2" MTL stud, 1 layer 5/8" each side, 6" above ceiling1429.5 ft1 x 22,698
W33-5/8" MTL stud, 2 layers 5/8" Type X each side, deck to deck4012 ft2 x 21,920
Total2686,682

Line by line: 86 x 12 x 1 x 2 = 2,064 SF. 142 x 9.5 x 1 x 2 = 2,698 SF. 40 x 12 x 2 x 2 = 1,920 SF. The total is 6,682 SF of board before openings and waste. In 4x12 sheets (48 SF each), that is 6,682 / 48 = 139.2, so 140 sheets before waste.

Track is simpler: top and bottom on every wall, so 268 LF x 2 = 536 LF. Studs come from the spacing: at 16 inches on center, each wall run needs its length in inches divided by 16, plus one, before corners and openings.

Now see what the height line is worth. If you misread Type W2 as deck to deck, you would carry 142 x 12 x 2 = 3,408 SF instead of 2,698 SF, an extra 710 SF. Missing the second layer on Type W3 would cut 960 SF the other way. Decide how you handle door and window openings, write it down, and add waste on top; published construction waste factors are a starting point.

Common mistakes reading partition types

Measuring wall types on the PDF

The slow part is getting linear feet per wall type. In MeasureFloorPlan you set the scale from one printed dimension, then click the runs for each wall type with the Distance tool and group them into named line items, such as Type W1 and Type W2, each with its own subtotal. Room traces also give wall and ceiling area per room, and the drywall preset turns area into sheet counts with your waste. More on that in drywall takeoff software.

Measure Plans in Minutes

Upload your full plan set. Get every length, area and count. Export the takeoff to Excel.

A floor plan drawing, not a photo of a room.
Plans from $9 a month. 100% money-back guarantee.

Frequently Asked Questions

Is a wall type legend the same as a wall type schedule?

Yes. Drawings call it a wall type legend, wall type schedule, partition types or partition schedule. All of them do the same job: each tag on the floor plan points to one entry that describes how that wall is built.

What does deck to deck mean on a wall type?

The wall runs from the floor deck all the way up to the underside of the structure above, not just to the ceiling. Board on a deck to deck wall covers the full floor to structure height, so it takes more material than a wall that stops above the ceiling.

What does STC mean in construction?

STC stands for Sound Transmission Class, a single number rating of how well a wall or floor blocks airborne sound. It is defined in ASTM E413 from lab tests run under ASTM E90. A higher number blocks more sound.

What is Type X drywall?

Type X is fire resistant gypsum board with glass fibers mixed into the core, which helps it hold together longer in a fire. Legends for rated walls name it directly, as in 5/8 inch TYPE X GYP BD.

What if a wall on the floor plan has no tag?

Check the general notes on the floor plan and the legend sheet for a default wall type. If there is none, list the wall as an assumption in your bid or send an RFI before you price it.

Measure Plans in Minutes

Upload your full plan set. Get every length, area and count. Export the takeoff to Excel.

A floor plan drawing, not a photo of a room.
Plans from $9 a month. 100% money-back guarantee.