Home › Learn › How to Read Elevation Drawings: Exterior, Interior and Takeoff Math
Part of: What Is a Takeoff in Construction? How to Do One From Plans
How to Read Elevation Drawings: Exterior, Interior and Takeoff Math

To read elevations, match each view to its wall with the title or the marker on the plan, then read the level datums for heights and the notes for materials. Widths come from the plan, heights come from the elevation, and together they give you wall, siding, masonry and tile areas. Elevations are one of the views you work through when you read blueprints for construction, and they hold most of the vertical numbers a takeoff needs.
Measure Plans in Minutes
Upload your full plan set. Get every length, area and count. Export the takeoff to Excel.
A floor plan drawing, not a photo of a room.
Plans from $9 a month. 100% money-back guarantee.
What does an elevation drawing show?
An elevation is a straight-on view of one side of a building, or of one wall inside a room, drawn with no perspective. For the definition and the drawing conventions, see the elevation drawing glossary entry. For a bid, what matters is the heights and materials it gives you.
Because there is no perspective, anything that is parallel to the sheet measures true to scale. That is what makes elevations useful for takeoff. A sloped roof plane or a wall that angles away from you does not measure true, so take those from the roof plan or the floor plan.
Exterior elevation vs interior elevation
An exterior elevation shows a whole side of the building: grade line, foundation, wall cladding, windows, doors, trim, roof edges and the heights that tie them together. A typical set has one for each side.
An interior elevation shows a single wall inside a room. Architects draw them where the wall carries more than paint: kitchen cabinets and backsplash, bath tile, wainscot, built-ins and wall-mounted fixtures. They are usually drawn at a larger scale than the floor plan, so check the scale under each view title.
How are elevations named and found?
Exterior elevations are named by compass direction. As the Wikipedia article on architectural drawing puts it, each elevation is labelled in relation to the compass direction it faces. The North Elevation shows the north-facing side, so check the north arrow on the plan before you match a view to a wall.
In U.S. National CAD Standard sheet numbering, sheet type 2 is elevations, so exterior elevations usually sit on A-2xx sheets. Interior elevations often land on large-scale sheets (type 4) or on interiors sheets, depending on the office.
Elevation markers on the floor plan
Interior elevations are found through markers on the floor plan. The marker is usually a circle with one to four arrows, each pointing at a wall that has an elevation drawn. On the Archtoolbox symbol reference, the top line of the interior elevation symbol is the drawing number and the bottom line is the sheet number. Letters mark sub-drawings.
So a circle reading 2 over A-401, with its arrow pointing at the kitchen's east wall, means the east wall is drawn as view 2 on sheet A-401. Exterior elevation markers work the same way when a set uses them. Symbol styles vary between offices, so check the legend on the general sheet.
What heights do you read on an elevation?
Heights are shown with level datums: a horizontal line across the drawing with a symbol and a label at the end. A drafting assignment from Bellevue College shows the pattern: FIRST FLOOR +0'-0", SECOND FLOOR +10'-0", T.O. PLATE +20'-0", RIDGE +28'-0". Each value is measured from the same zero.
- Finish grade: the ground line at the base of the building, drawn as a heavy line.
- Finished floor: the zero line on most residential sets. Confirm what the zero is tied to before you subtract.
- Top of plate (T.O. PLATE): the top of the wall framing, where the roof framing starts.
- Ridge: the high point of the roof.
- Window and door heads: given above finished floor (AFF), sometimes as a note and sometimes as a dimension.
Subtract datums to get the heights you need. In the Bellevue example the second floor is at +10'-0" and the plate at +20'-0", so the second-floor wall runs 20 - 10 = 10 ft from floor to plate. Opening sizes and head heights should agree with the window schedule and the door schedule; if they don't, flag it.
Materials, trim and notes
Materials are shown two ways: a hatch or texture over the area, and a leader note naming the product, like HORIZ. 1X4 CEDAR T&G SIDING or ASPHALT COMPOSITION SHINGLE on the Bellevue example. Read the note, not just the hatch, because two sidings can share a similar pattern.
Look for where one material stops and another starts. A brick wainscot, a band of board and batten in a gable, or stone at a column base each needs its own takeoff line. Trim (corner boards, window casing, frieze and rake boards) is a linear-foot item you measure along the lines on the elevation.
How do you take off siding from an exterior elevation?
Here is a sample south elevation of a one-story gable end, drawn to the numbers used below. It is an illustration, not a real project.
Wall area first. The rectangle below the plate is 28 ft wide and 9 ft from finished floor to plate, so 28 x 9 = 252 SF.
Then subtract the openings. The door is 3 ft by 6 ft 8 in, which is 3 x 6.67, or about 20 SF. The two windows are 4 x 4 = 16 SF each, so 32 SF. Openings total 52 SF, leaving 252 - 52 = 200 SF of siding on the wall.
Then the gable. A gable is a triangle, so its area is half the base times the height: 0.5 x 28 x 7 = 98 SF. The 7 ft height checks against the pitch. Half the 28 ft width is 14 ft, and 6:12 means 6 in of rise per 12 in of run, so 14 x 6 / 12 = 7 ft.
Net siding for this elevation is 200 + 98 = 298 SF. Repeat for each elevation, add them up, then add waste. Use the dimension to the gable peak, not the ridge datum, when they differ, since a ridge height may be measured to the top of the roofing. And check the wall section for where siding actually starts at the bottom; this sample starts it at the floor line.
Masonry works the same way. If the elevation showed brick to 3 ft above finished floor across the full 28 ft, that band is 28 x 3 = 84 SF, less any opening that dips into it, and the siding above it shrinks by the same amount.
How do you take off tile from an interior elevation?
Say a kitchen interior elevation shows a 10 ft counter run, with the backsplash running 1 ft 6 in from the countertop to the underside of the upper cabinets. Over the sink is a 3 ft wide window whose sill sits 6 in above the counter, so the window takes the top 1 ft of the backsplash for 3 ft.
| Line | Math | Area |
|---|---|---|
| Gross backsplash | 10 ft x 1.5 ft | 15 SF |
| Less window | 3 ft x 1.0 ft | - 3 SF |
| Net backsplash tile | 15 - 3 | 12 SF |
Wainscot and bath tile read the same way: the elevation gives the height (for example, a note reading tile to 4'-0" AFF) and the floor plan gives the wall lengths. Multiply, subtract openings, and keep each tile type on its own line. For quick wall math with openings, a wall square footage calculator does the subtraction for you.
Reading elevations alongside the rest of the set
Elevations give heights, but ceiling heights inside the building come from the sections and the reflected ceiling plan. Wall lengths come from the floor plan. Opening sizes come from the schedules. When two sheets disagree on a height, write it down and ask before you bid.
In MeasureFloorPlan, every sheet of a PDF set keeps its own scale. Set the scale on the elevation sheet from a printed dimension, trace a wall face or gable for area, click runs of trim for linear feet, and export the quantities to Excel (CSV) or PDF with the rest of the takeoff.
Measure Plans in Minutes
Upload your full plan set. Get every length, area and count. Export the takeoff to Excel.
A floor plan drawing, not a photo of a room.
Plans from $9 a month. 100% money-back guarantee.
Frequently Asked Questions
What is the difference between an exterior and an interior elevation?
An exterior elevation is a flat view of one whole side of the building: walls, roof, windows, doors and cladding. An interior elevation is a flat view of one wall inside a room, used where that wall has cabinets, tile, wainscot or mounted items that a floor plan cannot show.
What is an elevation marker on a floor plan?
It is a symbol, usually a circle with one or more arrows, that points at the wall being drawn. The top of the circle gives the drawing number and the bottom gives the sheet number, so 2 over A-401 means drawing 2 on sheet A-401.
Is a north elevation the side that faces north?
Yes. Elevations are labeled by the compass direction the wall faces, so the north elevation shows the north-facing side of the building. Check the north arrow on the site plan or floor plan to match each elevation to its wall.
What does +9'-0" T.O. PLATE mean on an elevation?
It is a level datum. It says the top of the wall plate sits 9 feet above the zero line of the drawing, which is usually the first finished floor. Subtract one datum from another to get a height, such as the wall height for siding.
How do you read elevations on civil or site plans?
On civil and grading plans, an elevation is usually a number rather than a drawing: a spot height in feet above a benchmark or datum named on the civil sheets. That is a different read from an architectural elevation view, and the civil sheet notes say what the zero is tied to.