Home › Learn › Section Drawing: How to Read One and What to Take Off
Part of: What Is a Takeoff in Construction? How to Do One From Plans
Section Drawing: How to Read One and What to Take Off

A section drawing shows the building as if it were sliced straight down and you were looking at the cut face. It is where you read the heights a floor plan cannot give you: ceiling heights, plate heights, roof pitch and footing sizes. For a takeoff, those numbers turn floor plan perimeters into wall area, drywall sheets and concrete yards.
Measure Plans in Minutes
Upload your full plan set. Get every length, area and count. Export the takeoff to Excel.
A floor plan drawing, not a photo of a room.
Plans from $9 a month. 100% money-back guarantee.
What is a section drawing?
A cross section represents a vertical plane cut through an object. Everything the cutting plane passes through is drawn with a bold line, often with a solid fill, so you can tell what was cut from what is just visible beyond it.
A floor plan is also a cut, just a horizontal one taken a few feet above the floor. The section turns that view on its side. That is why sections are the drawings that explain how one level relates to the next.
How do you read a section cut symbol on the plan?
The section cut symbol is a line drawn across the floor plan with a marker at one or both ends. It tells you three things: where the cut was taken, which way you are looking, and where to find the drawing.
- The line is the cutting plane. Everything it crosses shows up cut in the section.
- The arrow or flag on the bubble points in the direction of view.
- The top of the bubble is the section number (or letter).
- The bottom of the bubble is the sheet that section is drawn on.
On the target sheet, the drawing title repeats the same number and usually prints the scale under it. If a marker or note uses a short form you don't recognize, a list of construction abbreviations will usually decode it.
Building section vs wall section vs detail section
Plan sets work from big to small. The building section calls out wall sections, and the wall sections call out details. Each step is drawn at a larger scale with more notes.
| Type | What it cuts | What you read from it |
|---|---|---|
| Building section | The whole building, at a small scale | Floor-to-floor heights, ceiling heights, roof shape and pitch, stairs |
| Wall section | One exterior wall, footing to roof, at a larger scale (often 3/4" or 1/2" = 1'-0") | Footing and foundation, wall layers, insulation, plate height, window heads |
| Detail section | One connection along that wall, larger still | Flashing, sill plates, how one material meets the next |
Under the U.S. National CAD Standard numbering, the digit after the discipline letter is the sheet type, and 3 is sections. So A-301 is a typical first sheet of architectural sections. Structural sections, with footing and beam details, show up on the S sheets.
What can you read from a section drawing?
Most of what a section gives you is vertical: heights, depths and slopes. Here is what to look for and where it goes on your takeoff.
- Level lines and floor-to-floor heights, which set stair runs and stud lengths.
- Ceiling height, measured from finished floor to finished ceiling. This drives wall area.
- Plate height, the top of the wall framing. It can differ from the ceiling height when there is a soffit or a dropped ceiling.
- Roof pitch, shown as a small slope triangle such as 6 over 12.
- Footing width and depth, plus slab and foundation wall thickness.
- Insulation and assemblies, named layer by layer on the wall section.
How to read a section drawing, step by step
- Find the cut line on the floor plan and note which way the arrows point.
- Go to the sheet named in the bottom of the bubble and find the matching drawing number.
- Read the scale printed under that drawing title before you measure anything.
- Find the level lines and the finished floor elevation, then read up to the ceiling and the plate.
- Read the roof slope triangle and the footing dimensions.
- Follow any callouts to wall sections and details for the assembly layers.
- Write each height on your takeoff sheet with the section number it came from.
Step 3 matters because a building section and the wall section next to it are rarely at the same scale. If scaling drawings is new to you, see how to read an architectural scale. A printed dimension always beats a scaled one.
Section drawing takeoff: a worked example
Say the floor plan shows a 14 by 12 foot bedroom, the building section shows a 9 foot ceiling, the wall section shows a 20 inch wide by 10 inch deep continuous footing, and the roof triangle reads 6 over 12. The foundation perimeter is 140 LF and the roof covers 1,200 SF in plan.
| Item | From the section | Math | Result |
|---|---|---|---|
| Bedroom wall area (paint, gross) | 9 ft ceiling | (14 + 12) x 2 = 52 LF, x 9 ft | 468 SF |
| Bedroom drywall, walls + ceiling | 9 ft ceiling | 468 + (14 x 12 = 168) | 636 SF |
| Drywall sheets, 4x12 | 636 / 48 SF per sheet = 13.25 | 14 sheets before waste | |
| Footing concrete | 20" x 10" footing | 140 x (20/12) x (10/12) = 194.4 CF, / 27 | 7.2 CY before waste |
| Roof area on the slope | 6 in 12 pitch | Slope factor = sqrt(12² + 6²) / 12 = 1.118; 1,200 x 1.118 | 1,341.6 SF |
Look at how far one height moves the numbers. Read the same bedroom with an 8 foot ceiling and the wall area drops to 52 x 8 = 416 SF. That is 52 SF of board and paint per room you would miss, or overbuy, by guessing.
The wall line here is gross, with no deductions for the door or window. A wall square footage calculator handles openings if you subtract them. For whole jobs, the same perimeter times ceiling height method runs through drywall takeoff software, and the footing length times cross section works the same way in concrete takeoff software.
When the section and the plans disagree
Check that the ceiling height on the building section matches the reflected ceiling plan, which tags each room's ceiling height. If one room has a dropped ceiling or a soffit, the RCP usually shows it and the building section may not, because the section only shows where it was cut.
When two sheets conflict, don't just pick one. Write the question in your notes column and send an RFI or carry the higher number with a clarification in the bid. For where sections fit among the other sheets, see how to read blueprints for construction.
Measuring from sections and plans
In MeasureFloorPlan you set the scale from one printed dimension, trace each room once, and get floor, wall and ceiling area per room using the ceiling height you read from the section. Lengths, areas and counts export to Excel (CSV) or PDF. Pricing starts with a free demo on a sample plan, then Starter at $9 a month for 3 plans or Pro at $29 a month for unlimited plans, with a 48-hour money-back guarantee.
Measure Plans in Minutes
Upload your full plan set. Get every length, area and count. Export the takeoff to Excel.
A floor plan drawing, not a photo of a room.
Plans from $9 a month. 100% money-back guarantee.
Frequently Asked Questions
What is the difference between a building section and a wall section?
A building section cuts through the whole building at a small scale and shows how the levels, roof and stairs relate. A wall section cuts through one exterior wall from footing to roof at a larger scale and names every layer of the assembly.
What does the section cut symbol mean?
It marks where the building was sliced and which way you are looking. The arrow or flag points in the viewing direction, the top of the bubble is the section number and the bottom is the sheet where that section is drawn.
What is the difference between a section and an elevation?
An elevation shows the outside face of the building, the way you would see it standing in front of it. A section shows what you would see if the building were cut open, so it reveals floor framing, ceiling heights, insulation and footings that an elevation hides.
What scale are section drawings?
Each section has its own scale printed under its title, and you should always read that one. Building sections are usually drawn smaller than wall sections, and details called out from a wall section are drawn larger still.
Where are the sections in a plan set?
Under the U.S. National CAD Standard sheet numbering, the digit after the discipline letter tells you the sheet type, and 3 means sections. So architectural sections usually live on sheets like A-301 and A-302.