How much square footage discrepancy is acceptable in an appraisal?

There is no single universal tolerance. Fannie Mae uses a practical guideline of roughly 10% variance before requiring explanation or adjustment. FHA and VA do not publish specific tolerances. Most lenders expect the appraiser to measure independently and reconcile any difference from public records or MLS data. If the discrepancy materially affects value, it must be disclosed and adjusted for in the appraisal report.

Home / FAQ / Square footage discrepancy

How Much Square Footage Discrepancy Is Acceptable?

Square footage discrepancies between an appraiser's measurement and public records, MLS listings, or tax assessments are common. The question is: when does a discrepancy become a problem, and what are appraisers required to do about it? The answer depends on the lender, the loan program, and how much the variance affects value.

No single universal threshold exists

ANSI Z765-2021, Fannie Mae guidelines, FHA requirements, and VA guidelines do not specify a single “acceptable” variance in square footage. There is no official rule that says discrepancies under 2% are fine or that anything over 5% triggers a review.

What matters in practice is whether the discrepancy is material: meaning it would affect the appraiser's opinion of value, the market adjustment used for GLA, or the lender's underwriting decision.

Fannie Mae's practical guidance

Fannie Mae's Selling Guide requires appraisers to measure the subject property independently. If the appraiser's measurement differs materially from public record data, the appraiser must reconcile the discrepancy in the report.

In practice, many appraisers and AMCs use a rough guideline of ±10% variance as a soft threshold for flagging. If the appraiser measures 1,800 sq ft and the county record shows 2,000 sq ft (11% difference), that typically requires explanation. At 50 sq ft on a 2,000 sq ft home (2.5%), most reviewers will not question it.

The actual test Fannie Mae applies is not percentage-based: it is value-based. If the appraiser uses a GLA adjustment of $50/sq ft, a 100 sq ft discrepancy creates a $5,000 value impact. That is material for most loan amounts and must be addressed.

FHA and VA loans

FHA does not publish a specific square footage tolerance in its Single Family Housing Policy Handbook (4000.1). The expectation is the same as Fannie Mae: the appraiser measures the property, uses ANSI Z765 methodology, and notes any material discrepancies from public records.

VA guidelines similarly require independent measurement and reconciliation of material discrepancies, without specifying a percentage threshold.

Individual lenders and AMCs may impose their own tighter tolerances. It is not uncommon for an AMC to flag a report if the appraised square footage differs from MLS data by more than 5%, even if the methodology is sound. This is a lender overlay, not a GSE requirement.

Common causes of discrepancies

Tax records use outdated or estimated data. County assessors often rely on builder records or historical measurements, not field verification under ANSI Z765. A 100–200 sq ft difference from tax records on an older home is not unusual.
MLS data is often unverified. Listing agents frequently pull from tax records or prior listings. MLS square footage is not a measurement: it is reported data. Appraisers should not use it as the baseline.
Interior vs exterior measurement. Some older reports used interior measurements; ANSI Z765 requires exterior. This alone can cause consistent 50–150 sq ft discrepancies on homes with thick exterior walls.
GLA methodology differences. Finished basement included as GLA in old records but excluded under current ANSI rules. This is a frequent source of discrepancy in areas with older assessor data.
Measurement error. Human error in field measurements, especially on complex footprints with many angles.

What appraisers must do when there is a discrepancy

Measure independently. The appraiser's own measurement is the authoritative figure: not tax records, not MLS, not a prior appraisal.
Disclose the discrepancy. Note the difference between your measurement and public records in the appraisal report. Do not ignore it.
Explain the cause if known. “County records include the finished basement in total square footage; appraiser's GLA figure excludes below-grade finished area per ANSI Z765” is a complete, defensible explanation.
Adjust comparables consistently. If your subject is 1,850 sq ft and you are comparing to homes where the MLS data shows 2,000 sq ft, verify whether those comps are also overstated. Inconsistent adjustment bases create appraisal risk.

When a discrepancy becomes a serious problem

A square footage discrepancy becomes a material problem when:

It affects the appraiser's per-square-foot adjustment line item by a meaningful dollar amount
It causes the subject to rank differently against comparables (e.g., the smallest vs. mid-range comp)
It changes the property's conformity to the neighborhood
The lender or AMC flags it during review and requires a response
The discrepancy suggests possible unpermitted additions or demolitions (square footage decreased)

In these cases, the appraiser may need to file a revised report, provide an addendum explaining the variance, or in some situations revisit the property.

Reducing discrepancy risk

The best way to avoid defensible measurement disputes is to use a consistent, documented methodology. ANSI Z765 measurement from the exterior, with scale set from a verified wall dimension, gives you a defensible number you can explain step by step.

If you upload a floor plan to MeasureFloorPlan, trace the exterior perimeter, and set the scale from a confirmed exterior wall measurement, your GLA figure is tied to a specific, verifiable methodology. That is easier to defend in an audit or ROV than a rough estimate or interior-based calculation.